Protea

Protea 2000 In-Situ Infra-red gas analyser connected to a Protea Control Unit forms the basis of a Continuous Emission Monitoring System (CEMS). The Stack Mounted In-Situ analyser monitors the stack gas without the need for any sample handling equipment making it a cost effective solution to Continuous Emission Monitoring and Process applications. The analyser monitors the stack gases "wet", water vapour is continuously monitored enabling the pollutant gases can be reported on a wet or dry basis. Certification with environmental monitoring equipment standards is dependent on analyser series and application. Certification of models includes EN 15267-3 MCERTS; EN 14181 QAL 1 and US EPA 40cfr part 60 & 75. Certified for use in Hazardous Areas Option.

P2000D is an combined infra-red (IR) and Ultra Violet (UV), duct or stack-mounted Analyser, designed to provide In-Situ analysis of up to eight gas-phase emission components. A typical system comprises of a stack mounted Analyser, an integral Calibration Module and a Control Unit with options which include a powerful In-Situ Heater and a stand-alone Analysis Software package.

P5000 is an ultra-violet (UV), continuous emission monitoring analyser, designed for in-situ analysis of gas-phase emission components. Using absorption spectroscopy, P5000 stores and analyses the full UV spectrum and calculates the gas emission concentrations. A typical system comprises an in-situ analyser and a Control Unit. P5000 uses the reflective beam principle to directly measure process gas as it enters the insitu sample cell. Unlike higher maintenance extractive systems, Protea's patented, sintered metal technology removes the need for gas filtering or sample conditioning. The P5000 incorporates an auto verification unit which initiates zero and calibration checks ensuring compliance with international regulatory requirements. In addition the advanced dynostics reduces operator interventions and maintenance requirements.

Protea P7000 is a Bio Gas Multi-Gas Analyser designed to continuously monitor process gas from Land Fill, Bio Gas and Natural Gas. It offers a low cost of through-life ownership combined with proven technology.

atmosFIR CEM is a complete emissions monitoring system incorporating the atmosFIR 19" FTIR analyser. As completely hot and wet emissions measurement, atmosFIR CEM is ideal for complete measurement of multiple gases from applications such as incineration and power. A standard gas suite of NO, NO2, N2O, SO2, NH3, HCl, HF, CH4, O2, CO2 and H2O is provided, but with the powerful FTIR analyser, further gases can be added easily in software. At the heart of system is the high-resolution, robust and proven FTIR spectrometer offering high signal throughput, low-noise and long lifetime of components. atmosFIR has been developed to incorporate the latest improvements and advantages in technology, The atmosFIR FTIR analyser contains an in-built sampling system and is designed for ppm-level emissions monitoring.

AtmosIR is a hot, wet, extractive, multi-component analyser designed to monitor up to six gases simultaneously via the NDIR-GFC technique. AtmosIR is a 19" rack mountable analyser featuring Protea's proven photometer, taken from our MCERTS approved P2000 analyser, combined with our hot/wet gas cell technology as found in our FTIR gas analysers. AtmosIR is provided ready to install in a fixed cabinet system by Protea, an OEM or system integrator. This includes all power and alarm for a heated sampling system, together with I/O for integration with plant control systems.

Same specification as the atmosIRw fitted with a HMI and I/O unit. Incorporates analogue transmitters (0—20mA, 4—20mA, 0—5V) one per monitored range optional relays and digital inputs. Each unit can accept analogue inputs from third party analysers / sensors for example stack flow, particulates, pressure using the data to report in mass units ie kg/hr.

Extractive Infra-Red multi component analyser housed in a 19" 5U chassis utilising a 4.2m multi pass cell, capable of monitoring up to six (6) gases. Fitted with a auto verification module will automatically zero and verify calibration by introducing test gas directly into the cell or sample probe. The monitored concentrations (ppm, mg/m3, %), diagnostics, data logging and plant interface are a function of the analyser control unit Protea P-PC or Protea P-HMI which can support multiple analysers.

Transportable Extractive Infra-Red multi component analyser housed in a rugged case, can be used as a transportable source testing analyser or back up CEMs in the event of the fixed CEMS failure. Same specification as the atmosIRr and atmosFIRi incorporating HMI.

AtmosIR is a hot, wet, extractive, multi-component analyser designed to monitor up to six gases simultaneously via the NDIR-GFC technique. Installing as an emissions monitoring system will ensure compliance with international performance standards. AtmosIR features Protea's proven photometer, taken from our MCERTS approved P2000 analyser, combined with our hot/wet gas cell technology as found in our FTIR gas analysers. AtmosIRw provides the gas analyser ready to install in a fixed, integrated Continuous Emission Monitoring (CEM) system.

Protea P300 is an infra-red (IR), extractive multi component analyser to provide analysis of up to six gas-phase or liquid process components. The analyser is certified for installation in hazardous area with options including, high pressure sample cell, heated sample cell and built in HMI with standard industrial communication.

The Protea Analyser Control Units form the hub of an advanced Continuous Emission Monitoring System. In addition to collecting data from Protea's advanced range of Emission Monitoring Analysers, it is configured to receive data from complementary devices, e.g. Dust / Opacity, Oxygen and Flow. This enables the system to display gas concentrations on a normalised basis and, if required, in mass units eg Kg/hour.

The Protea HMI forms the hub of an advanced Continuous Emission Monitoring System (CEMS). The Protea - HMI is capable of supporting up to four Protea Analysers with associated third part devices. In addition to collecting data from Protea's P2000 and P5000 analysers, it is configured to receive data from complementary devices, e.g. Dust / Opacity, Oxygen and Flow. This enables the system to display gas concentrations on a normalised basis and, if required, in mass units e.g. Kg/hour. The analyser communicates via a serial data link to the control unit, which can be located up to 1200m from the CEMS.

The Solus Multipoint NH3 Ammonia gas analyser is ideal for ambient air and livestock monitoring applications of Ammonia (NH3). The Solus is a complete transportable ammonia measurement solution for up to 10 sample points. Ammonia is a primary measurement parameter under the Verification of Environmental Technologies for Agricultural Production (VERA) Test Protocol for Livestock Housing and Management Systems.

The 204M is a transportable CEM based on FTIR technology. Using the 204M for measurements of waste incineration and combustion plant process is as simple using an FTIR can be. With pre-loaded calibration methods for 28 gas species, automatic nitrogen purging, in-built pressure and temperature alarms, analogue and digital I/O it is a complete site-ready back up CEM. The ProtIR 204M and PAS software have been designed to allow stack emission monitoring to be carried out to the Environment Agency's Technical Guidance Note M22 as simply and quickly as possible.

The Protea marine CEMS has been designed for minimal intervention with a high availability, in addition the systems operate a comprehensive diagnostic routine. The Protea 2000 emissions monitoring system is approved for the analysis of exhaust gases from the engines and boilers of ships and offshore rigs. Robust and with proven reliability, up to six gases can be measured including SO2, CO2 and NOx. The need to demonstrate environmental responsibility is key for today's marine and offshore industries.

Protea's range of Fourier Transform Infrared (FTIR) Gas Analysers allows for the measurement of nearly any gas with one instrument. A FTIR gas analyser collects a full infrared spectrum continuously, allowing for hundreds of gases to be detected and measured at once. Changes are only needed to software calibration files to measure new gases. atmosFIR is the successor to Protea's previous emissions monitoring FTIR systems, keeping all the features that users found valuable in achieving their measurement results.

Protea's range of Fourier Transform Infrared (FTIR) Gas Analysers allows for the measurement of nearly any gas with one instrument. A FTIR gas analyser collects a full infrared spectrum continuously, allowing for hundreds of gases to be detected and measured at once. Changes are only needed to software calibration files to measure new gases. atmosFIR EX is an ATEX certified gas analyser system for measurement of industrial gases in a Zone 1 or Zone 2 area, providing a complete EX certified gas measurement system that meets both the sampling of non-flammable and flammable gases.

The atmosFIRair mobile gas analyser allows for immediate, continuous measurement of 1000's of gases. Based on the same atmosFIR Fourier Transform Infrared (FTIR) analyser platform Protea uses in environmental emissions measurements, atmosFIRair is a powerful tool for monitoring of ambient air pollution, emergency response and also analytical applications such as greenhouse gas (GHG) testing. atmosFIRair is the latest generation of FTIR gas analyser technology from Protea in a portable or mobile form.

Protea's range of Fourier Transform Infrared (FTIR) Gas Analysers allows for the measurement of nearly any gas with one instrument. A FTIR gas analyser collects a full infrared spectrum continuously, allowing for hundreds of gases to be detected and measured at once. Changes are only needed to software calibration files to measure new gases. 20 metre pathlength FTIR gas analyser for low concentration laboratory or process measurements. Configurable with 3 detector types for ppb level gas detection and reporting.

Protea's range of Fourier Transform Infrared (FTIR) Gas Analysers allows for the measurement of nearly any gas with one instrument. A FTIR gas analyser collects a full infrared spectrum continuously, allowing for hundreds of gases to be detected and measured at once. Changes are only needed to software calibration files to measure new gases. atmosFIRi is a new concept in FTIR. The unit is designed as a general gas analyser that is simple to use, portable and a very low cost product that provides real-time online measurement suitable for plant systems.

Protea's range of Fourier Transform Infrared (FTIR) Gas Analysers allows for the measurement of nearly any gas with one instrument. A FTIR gas analyser collects a full infrared spectrum continuously, allowing for hundreds of gases to be detected and measured at once. Changes are only needed to software calibration files to measure new gases. atmosFIRt is the latest generation of FTIR gas analyser technology from Protea in a portable or mobile form.

Protea's range of Fourier Transform Infrared (FTIR) Gas Analysers allows for the measurement of nearly any gas with one instrument. A FTIR gas analyser collects a full infrared spectrum continuously, allowing for hundreds of gases to be detected and measured at once. Changes are only needed to software calibration files to measure new gases. atmosFIR is the latest generation of gas analyser technology from Protea. The atmosFIR system improves upon previous FTIR technology and represents one of the most cost-effective and flexible analytical products on the market today.

Solus is a stand-alone gas monitoring unit designed for precise measurements of single component gases. The Solus platform represents an extension of Protea's spectroscopic gas analysis equipment into laser based technology, allowing for highly selective, quick response and low range measurements of 1 or 2 gases in a cost-effective, re-configurable package. Solus utilises the latest in Tuneable Laser Diode (TDL) spectroscopy, together with the best in micromachining technology, to deliver a precisely controlled narrow wavelength that can be tuned over a small range.

The atmosFID Total VOC Analyser is designed for Continuous Emissions Monitoring (CEM) of gaseous VOC emissions from a wide range of sources – waste incineration, combustion sources, paint shops and manufacturing processes. As a 19" rack analyser it can be provided in a complete fixed emissions system from Protea, or can be used as a standalone analyser.